KAK Blade AR-15 Finish Your 9mm Pistol Kit
KAK Industry Complete Mil-Spec Lower Parts Kit (LPK)
A basic AR-15 lower parts kit. It includes all the small parts needed to complete your lower. This kit includes a standard right hand safety selector.
All Fire Control Parts are MPI Tested and Rockwell Tested
Made in the USA
By a major government contractor
Davidson Defense AR-15 Lower Parts Kit
The Lower Parts Kit includes:
Black A2 Pistol Grip
Pistol Grip Screw
Pistol Grip Lock Washer
Trigger Guard Roll Pin
Bolt Catch Spring
Bolt Catch Roll Pin
Magazine Catch Button
Magazine Catch Spring
Front Pivot Pin
Pivot Pin Detent Spring
Take Down Detent
Buffer Retainer Pin
Buffer Retainer Spring
KAK Shockwave Blade Pistol Stabilizer - Black
Shockwave is proud to introduce the patent-pending Blade pistol stabilizer. Made from high-strength glass-reinforced polymer, the Blade is manufactured to exacting tolerances and fits all pistols equipped with a standard AR-15 pistol buffer tube (up to 1.25” in diameter). No special receiver extension needed. No half-hour installation process. Just slip it on and tighten the large set screw for a rock-solid installation.
This veteran-designed and USA-manufactured shooting aid improves your marksmanship by providing additional support of your pistol while you still hold and operate it with one hand. The Blade incorporates a vertical "Fin" which you stabilize against the inside of your forearm when in the firing position. Or, you can stabilize the Blade against your cheek for a perfect, steady sight picture.
A FRACTION OF THE COST OF OTHER BRACE OPTIONS!
Fits all pistols equipped with a standard AR-15 pistol buffer tube (up to 1.25 in diameter) AR pattern, Glock, CZ Scorpion Evo 3, HK9X pattern, etc.
Available in black and flat dark earth (this listing is for black)
Quick and easy to install
Provides additional support during firing
Weighs a scant 5.0 ounces
ATF approved for pistol use
Veteran designed, engineered, marketed, and sold
Made in USA
Standard AR-15 Carbine Recoil Spring
Made of the finest spring steel rated for 20,000+ rounds
US Tactical Ind. Ar-15 M16 Mil-Spec Receiver End Plate
Maintains Proper Alignment of Stock & Buffer Tube
M4-style receiver plate includes the engagement tab required to align the buttstock and buffer tube with the lower receiver on carbine models.
Precision, fine blanking process ensures precise edges and superior flatness for correct fit and solid installation.
Made of 4140 Hardened Steel
Davidson Defense AR-15 Carbine Castle Nut
Fits both Commercial and Mil-Spec tubes. It's always good to have a spare!
KAK Industries AR-15 9MM Carbine Buffer
This 9mm buffer is designed to be used on new or converted AR-15 shooting 9mm. Depending on a number of factors including barrel length, a heavier buffer may work much better than the standard 3 oz buffer. It is also used to reduce cycle rate of the AR-15 and felt recoil. This is a 5.4 ounce filled buffer to facilitate correct timing, cycling and firing of 9 mm and 9 mm +P loaded ammunition.
Many 9mm AR-15's need a 5.4-5.8 oz buffer weight of buffer to cycle properly.
While designed specifically for the 9mm, they can be used to slow the cyclic rate of full automatic M-16 rifles/M4
This Buffer is made In the USA by KAK Industries and they are each quality inspected.
Buffer Color May Vary*
Pistol Buffer Tube
1 Mil-Spec Diameter Pistol tube (USA-made) diameter 1.25"
Made Of 6061 T6 Aluminum
High Quality Construction
Overall Length is 7 5/16"
Lakota Ops 9MM Nitride Bolt Carrier Group
- Accepts Glock and Colt mags
If you are looking to build a 9mm Rifle, then this bolt is exactly what you will need to ensure smooth cycling with any standard fire control group. Our bolts come with ramps in a nitride finish.
Designed to work with Colt & Glock Mags. Also this bolt uses colt extractors & firing pins so when it comes time to replace a wear part you will be easily able to find the replacement part
Unlike some 9mm bcg on the market that use proprietary extractors and firing pins.
Tungsten weighted to proper spec for reliable and safe use.
Machined from 8620 Steel
QPQ Black Nitride Finish
Compatible with both GLOCK and Colt Magazines
Ramped bolt for a standard AR-15 hammer
Features removable weight
AR-15 M4 Charging Handle Mil-Spec Quality
Machined from aluminum 7075 T6 forgings
Complete assembly including latch
Finished in Type III Hardcoat Anodized and Teflon Coated final finish for smoother operation